BLSBM - ACRY-SHIELD ACRYLIC FLAT FINISH, 1240-SERIE
- MSDS: BLSBM
- Manufacturer: KELLY MOORE PAINT CO INC
- Product Name: ACRY-SHIELD ACRYLIC FLAT FINISH, 1240-SERIE
- National Stock Number: 8010-00N022019
Product Identification
Product ID:ACRY-SHIELD ACRYLIC FLAT FINISH, 1240-SERIE
MSDS Date:06/30/1989
FSC:8010
NIIN:00N022019
MSDS Number: BLSBM
Responsible Party
SAN CARLOS, CA 94070
US
Emergency Phone: 800-424-9300(CHEMTREC)
Info Phone: 415-592-8337
Preparer: JULIAN SCHAFER
Cage: KELLY
Contractor
Telephone: 415-592-8337
Cage: KELLY
Ingredients
ETHYLENE GLYCOL (SARA III)
CAS: 107-21-1
RTECS: KW2975000
Fraction By Weight: <4%
OSHA PEL C 50 PPM
ACGIH TLV: C 50 PPM,VAPOR; 9192
EPA Report Quantity: 1 LB
DOT Report Quantity: 1 LB
PROPIONIC ACID, 2-METHYL-,MONOESTER
CAS: 25265-77-4
Fraction By Weight: <5%
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: DIZZINESS, HEADACHE, NAUSEA,
CONFUSION, IRRITATION TO UPPER RESPIRATORY TRACT, UNCON, SKIN AND
EYES IRRITATION. CHRONIC: NONE KNOWN.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:SEE YOUR PHYS FOR SPECIFIC MED
OPINION REGARDING YOUR CONDITION.
First Aid
First Aid:INHAL: REMOVE TO FRESH AIR. RESTORE BREATHING. CONSULT PHYS.
EYE: FLUSH WITH LARGE VOLUMES OF WATER FOR AT LEAST 15 MIN. GET MED
ATTN. SKIN: WIPE OFF WITH A RAG. WASH THOROUGHLY WITH SOAP AND
WATER. I NGEST: CONSULT HOSPITAL EMERGENCY ROOM OR POISON CONTROL
CENTER IMMED.
Fire Fighting
Flash Point:>200F,>93C
Extinguishing Media:NOT APPLICABLE. MEDIA SUITABLE FOR SURROUNDING FIRE
.
Fire Fighting Procedures:NONE. WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE (DUE TO
BUILDUP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME HEAT.
Accidental Release
Spill Release Procedures:VENTILATE AREA TO PREVENT BUILDUP OF VAPORS.
FOR SMALL SPILLS, SOAK UP WITH ABSORBANT. FOR LARGER SPILLS, DIKE
AREA WITH ABSORBENT MATERIAL AND SCOOP UP LIQUIDS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STORE UPRIGHT IN SEALED CONTAINERS
AWAY FROM HEAT AND FLAME.
Other Precautions:REMOVE AND WASH CONTAMINATED CLOTHING BEFORE REUSE.
Exposure Controls
Respiratory Protection:USE NIOSH/MSHA APPRVD PARTICLE MASK TO AVOID
BRTHG SPRAY MIST OR SANDING DUST IF LOC VENT IS ADEQ TO KEEP TLV
W/IN ACCEPTABLE LIMITS. IF LOC VENT IS NOT ADEQ, THE USE OF AN
NIOSH/MSHA APPRVD RESP FOR ORG VAP, SUPPLIED AIR OR SCBA IS RECOM.
Ventilation:LOCAL EXHAUST SUFFICIENT TO KEEP TLV BELOW PRESCRIBED
LIMITS.
Protective Gloves:RECOMMENDED.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
MFR TRADE NAME/PART NO: ALL COLORS.
Chemical Properties
HCC:N1
Boiling Pt:B.P. Text:212F,100C
Vapor Pres:SEE INGRED
Vapor Density:
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:52-62
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED TO DECOMPOSITION AS IN WELDING.
Disposal
Waste Disposal Methods:DISCARD IN LANDFILL IN SEALED METAL CONTAINERS
AWAY FROM HEAT AND FLAME AND IN ACCORDANCE WITH LOCAL, FEDERAL, AND
STATE REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.